What are the steps to configure a switch?

  1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
  2. Step 2: Set up management IP.
  3. Step 3: Check VTP revision number.
  4. Step 4: Configure access ports.
  5. Step 5: Configure trunk ports.
  6. Step 6: Configure access ports.
  7. Step 7: Set up VTY line config.

What is basic switch configuration?

The default configuration on the switch is to have the management of the switch controlled through VLAN 1. However, a best practice for basic switch configuration is to change the management VLAN to a VLAN other than VLAN 1. Then you will set the IP address of the switch to 172.17. 99.11 with a subnet mask of 255.255.

What is configuration checklist?

Configuration Checklist is a great tool for determining what configurations are missing or incomplete. Often clients are missing key configurations or a configuration is missing a key element, such as a Serial Number or Warranty Expiration.

How do I configure a switch port?

Switch ports can be manually configured with specific duplex and speed settings. Use the duplex interface configuration mode command to manually specify the duplex mode for a switch port. Use the speed interface configuration mode command to manually specify the speed for a switch port.

How many VLANs can we configure in a switch?

4096 VLANs
A switch supports a maximum of 4096 VLANs, among which VLANs 0 and 4095 are reserved for system use, and VLAN 1 is the default VLAN. Therefore, you can only create VLANs 2 to 4094. You can repeat the vlan command multiple times.

How is VLAN configured?

Generally three or four things must be configured on VLAN capable switches:

  1. Add/define the VLANs. Most switches have a means of defining a list of configured VLANs, and they must be added before they can be configured on any ports.
  2. Configure the trunk port.
  3. Configure the access ports.
  4. Configure the Port VLAN ID (PVID)

Why do we configure switches?

Switch allows us to set IP address on interface level. IP address assigned on interface is used to manage that particular interface. We also have to set default gateway IP address from global configuration mode. In following example we would assign IP 172.16.

How do I prepare for a deployment checklist?

A predeployment checklist for you and your service member

  1. File legal paperwork.
  2. Break contracts and pay future bills.
  3. Create a Family Care Plan, enroll in the Defense Enrollment Eligibility Reporting System and update Department of Defense ID cards.
  4. Plan for “combat pay”
  5. Figure out a communication strategy.

What is port configuration?

The Port Configuration window displays the port configuration and provides access to a window for modifying port configuration. Port configuration values are: Port. Slot and port number for each port installed in the switch (for example, A1 means the first port in slot A).

Can a port be in 2 VLANs?

When a port belongs to two or more VLANs of the same type, they remain as separate broadcast domains and cannot receive traffic from each other without routing. NOTE: If multiple, non-routable VLANs exist in the switch—such as NETbeui protocol VLANs—they cannot receive traffic from each other.

How do you set up an Ethernet switch?

Steps to Set up a Network Switch With a Router Step 1: Unplug all the power supplies of cable modem, network switch and wireless router. Step 2: Connect your modem to the telephone wire. Step 3: Plug the other end of the Ethernet cable connected with modem into your router’s WAN port.

How do you set up a Cisco switch?

Configuring a Cisco 3548 switch is very simple. Connect the Cisco 3548 switch’s console port with the computer’s com port by using the UTP roll over cable. After physical connection, make a HyperTerminal session and give it any name. The com port setting should be Restore Default in the com port’s properties.

What is switch configuration?

Basic Switch Configuration (2.1) Switches are one of the most numerous devices installed onto the corporate network infrastructure. Configuring them can be fun and challenging. Knowing how switches normally boot and load an operating system is also important.

What is the configuration of router?

Basic configuration of the router includes configuration of the IP address, default routing, static and dynamic routing, static and dynamic NATing, host name, banner, secret password, user accounts, and other options.